Produktai skirti kompiuterinė atmintis (139)

Together with the EBGS2971 Evaluation Board, this document serves as a guide for evaluating the GS2971; a Gennum 3Gb/s, HD, SD SDI Receiver, with integrated equalizer. This document contains four main sections 1. Evaluation Board User Guide. 2. Evaluation Board Schematics. 3. Evaluation Board Layout. 4. Evaluation Board Bill of Materials The figure below shows a block diagram of the features and the functions of the EBGS2971. The board includes a power supply, a 3GSDI input, a 3GSDI loopthrough output, a GS2971 Receiver, a parallel video output connector, an audio output with four BNCs for AES audio, a fourpin header for serial audio, a JTAG/GSPI header, a 27MHz crystal, a DIP switch and some status indication LEDs. The GS2971 will automatically detect the input signal as SDSDI, HDSDI or 3GSDI. The

EP105 is a high speed 10bit LVDS (Low Voltage Differential Signal) transmitter capable of transmitting LVDS outputs at 150 Mhz clock rate. The chip adopts Explore’s proprietary eLVDS (Enhanced LVDS) technology which was developed for supper high speed LVDS interface. EP105 along with EP106 (eLVDS receiver) support single link transmission between the host and the flat panel display up to 1080p resolution. The chip converts 32 bits (10bits/color, 2 dummy bits) of CMOS/TTL data and 3 control bits into 5 LVDS data streams. At the maximum input clock rate of 150MHz, each LVDS differential data pair speed is 1.05 Gbps, providing a total throughput of 5.25 Gbps. The transmitter can be configured to input clock rising edge or falling edge strobe through an external pin. Support 8MHz to 150MHz clock rates from NTSC to 1080p resolution Up to 5.25Gbps bandwidth

MCS9901CVCC is a single lane multifunction PCI express to I/O controller. It supports two serial ports, one parallel port and six GPIO's. MCS9901CVCC also provides an option for peripheral expansion through proprietary Cascade interface. The generic cascade interface allows interconnecting with similar chips like MCS9900, MCS9950 to expand the peripheral ports. The serial ports are compatible with RS232, RS422 & RS485 standards and supports throughput from 50bps to 16Mbps. Parallel Port is compatible with IEEE 1284 and supports Nibble, Byte, SPP, ECP, and EPP modes. All the GPIO pins are programmable and can be used as Input or Output. An I²C interface is provided to configure MCS9901CVCC device options through an external EEPROM. PCI Express Singlelane (X1) PCI Express Endpoint Controller with integrated PHY Compliant with PCI Express Base Specification, Revision 1.1

Émetteursrécepteurs RS232 de faible puissance 5V 250Kbps (Caractéristiques 28 broches, w/o Wake Up, ±6V Output Voltage Swing) The ZT230E series devices are +5V powered EIA/TIA232 and V.28/V.24 communication interfaces with low power requirements. These transceivers consist of combinations up to five line drivers, five line receivers and the proprietary switchcapacitor regulated voltage converters. The ZT211E and ZT213E/AE feature a low power shutdown mode which draws as little current as 1µA typical with receiver outputs tristated and in wakeup. These devices operate from a single +5V power supply at the guaranteed data rate of 250K bits/sec with enhanced electrostatic discharge (ESD) protection in all RS232 I/O pins exceeding ±15kV HBM.

Multi-mode LTE Cat.M1/Cat.NB2/EGPRS+ GNSS Size: 19.9 x 23.6 x 2.3mm LGA package BG95 is a series of LTE Cat.M1/Cat.NB5/EGPRS module with integrated GNSS. It is fully compliant with 3GPP Rel. 14 specification and offers a maximum data rate of 375Kbps downlink and 1.2Mbps uplink. It features ultra- low power consumption by leveraging the integrated RAM/flash as well as the ARM Cortex A7 processor supporting ThreadX, achieving up to 70% reduction in PSM leakage and 85% reduction in eDRX current consumption compared to its predecessor. BG95 boasts a comprehensive set of hardware-based security features and enables trusted applications to run directly on the Cortex A7 TrustZone engine. As well, BG95 provides pin-to-pin compatibility with Quectel LTE module EG91/EG95, LPWA module BG96 & BC95, UMTS/HSPA module UG95/UG96 and GSM/GPRS module M95. Fast time-to-market:Reference designs, evaluation tools and timely technical support minimize design-in time

The MCS7832 USB to 10/100 Ethernet Controller is a unique solution to interface 10/100 BaseT Ethernet devices to the Universal Serial Bus (USB2.0). This device has been specifically designed to provide a simple, low cost solution to communicate with applications needing plugand play 10/100 Ethernet connectivity with minimal design time. This is accomplished by its highly integrated functionality, robust software suite, WHQL and USBIF certification, low pincount and high performance. It provides internal buffering to enable parallel operations from USB ports on the host side, and MAC ports on the Ethernet side. It also provides a serial interface for an EEPROM for storing the MACID, VID, PID, and other configurable settings. USB 2.0 Device Controller Supports HS (480Mbps) and FS (12Mbps) modes USB

Cliquer sur l'image afin de mieux voir

Quectel EG06 est une série de modules LTE Cat.6 optimisés spécialement pour les applications M2M et IoT Quectel EG06 est une série de modules LTE Advanced de catégorie 6 optimisés spécialement pour les applications M2M et IoT. Adoptant la technologie 3GPP Rel. 12 LTE, il offre des vitesses optimisées m2M de 300 Mbit/s downlink et 50Mbit/s uplink taux de données de pointe. Conçu dans le facteur de forme LGA, EG06 est compatible avec le futur module Cat.9 DE Quectel EG09, le module Cat.12 EG12 et le module Cat.16 EG16 , qui aidera les clients à migrer entre différentes catégories à l’avenir. EG06 contient 5 variantes (EG06-E, EG06-A, EG06-LA, EG06-APAC et EG06-AUTL) qui sont conçues pour différentes régions cibles et couvrent presque tous les principaux transporteurs de cours d’eau dans le monde entier. EG06 prend en charge la technologie de localisation Gen8C Lite de Qualcomm™® IZat (GPS, GLONASS, BeiDou, Galileo et QZSS). Améliorations des fonctionnalités:prend en charge DFOTA*, eCall* et DTMF

Cliquer sur l'image afin de mieux voir

Module sans fil ultra-compact et fiable SIM8905 basé sur la plate-forme LTE multi-mode Qualcomm MSM8909. GSM/GPRS/EDGE/EGSM:850/900/DCS1800 Supply voltage range:3.4 ~ 4.4 V Operation temperature:-25℃to +75℃ Dimension:40.5*40.5*2.8mm Weight:10.6g WCDMA/HSPA/HSPA+:42.2 Mbps(DL),11.5

SG-211 Series Frenquency range:1 MHz to 80 MHz Supply voltage:1.5 V Typ / 1.8 V Typ Function:Standby External dimensions:2.5 x 2.0 x 0.8 mm Output:CMOS

Lecteur de montage mur ou panneau, LF+HF+BLE et interfaces améliorées RS485, RS232, Wiegand, Horloge/Données, USB. Membre à part entière de la famille TWN4 ayant accès à un environnement SSK puissant, à un logement IP65 Enhances interfaces RS485, RS232, Wiegand, Clock/Data, USB Enhanced light concept, up to 5 individually programmable RGB LEDs Infrared tamper detection, front facing OSDP protocol on request Excellent RFID performance Allows enhanced security in your applications Only 43.8 x 40.8 x 28.5 mm (including connector) for OEM PCB version 9 to 30 V power supply Additional micro USB port support Integrated LF + HF + BLE antennas One on-board SAM sockets ID-000 for enhanced security Bluetooth Low Energy BLE module on board Firmware update via USB port Support of options P and PI for additional technologiesLegic version available as well Light” version with reduced set of features available as well

The AX88796C is a SPI or nonPCI Ethernet controller with low power, lowpincount and variable voltage I/O for the Embedded and Industrial Ethernet applications. The AX88796C supports 8/16bit SRAMlike or AddressData Multiplex interface with variable voltage I/O, providing a glueless connection to common or highend MCUs. The AX88796C also provides an alternative SPI slave interface for MCUs with SPI master for simplifying host interface connection. The AX88796C integrates onchip Fast Ethernet MAC and PHY, which is IEEE 802.3/802.3u 10BASET/100BASETX compatible, and embedded SRAM for packet buffering to accommodate high bandwidth applications.

Cliquer sur l'image afin de mieux voir

The RDK12GCONV UHD Converter Reference Design demonstrates the use of Semtech's GS12241 12G UHDSDI Retiming Adaptive Equalizer, GS12090 Bidirectional 12G UHDSDI Cable Equalizer/Driver, GS12281 12G UHDSDI Retiming Cable Driver, and GS12070 UHDSDI Gearbox to enable conversion from single channel 12Gb/s SDI, quad channel 3Gb/s SDI and other multiplexing or demultiplexing modes while minimizing the port count in designs. This reference design not only allows your evaluation of Semtech products; the source files for the schematic, PCB layout, microcontroller and GUI can be provided by contacting your local FAE to accelerate your time to market. Note This Reference Design assumes familiarization with the Semtech products found onboard the RDK12GCONV. For further information regarding these products, please refer to the following documents

The AX88772C USB 2.0 to 10/100M Fast Ethernet controller with Microsoft AOAC(Always On Always Connected) support is a high performance and highly integrated ASIC which enables a low cost, small form factor, and simple plugandplay Fast Ethernet network connection capability for desktops, notebook PCs, Ultrabooks, cradles/port replicators/docking stations, game consoles, digitalhome appliances, and any embedded system using a standard USB port. The AX88772C can be used in any embedded system with a USB host microcontroller requiring a twisted pair physical network connection. Featuring a USB interface (compliant with USB specification V2.0 and V1.1) to communicate with a USB Host Controller, the AX88772C

Sigfox RCZ1/3, module combo BLE 4.2The WS2118-00 module is a cost-effective, high performance, ultra-low power, sub-1GHz and Bluetooth® low energy RF devices. Very low active RF and MCU current and low-power mode current consumption provide excellent battery lifetime and allow for operation on small coin cell batteries and in energy-harvesting applications.The radio frequency supports SIGFOX RCZ1 and RCZ3. STM BlueNRG-1, S2-LP, sub-1GHz PA, 16MHz, 50MHz & 32.768KHz crystals, DC2DC, and U.FL connector on a single module. Stamp-hole 38pins package. Dimension 22mm(L) x 24mm(W) x 2.8mm(H) High performance, ultra-low power Cortex-M0 32-bit Microcontroller Programmable 160 KB Flash 24 KB RAM with retention (two 12 KB banks) Up to +8dBm BLE RF output power, up to +16 dBm sub-1GHz RF output power Excellent performance of receiver sensitivity. Up to -88dBm (BLE) and -130dBm (Sub-1GHz). Low Power and Wide Supply Voltage Range: 2.0 to 3.6V Low Power and Wide Supply Voltage Range:2.0 to 3.6V Operating temperature range:-40 °C to +85 °C

LTE Cat-M, NB-IoT, GPRS Support 3GPP Rel14 • Power Save Mode(PSM) and Extended Discontinuous Reception(eDRX), SIM7070G can extend battery life to 10 years. • CAT-M, NB-IoT , GPRS triple mode • Package 24x24mm / compatible with SIM7000/SIM800F/SIM900 • Interfaces: UART, SIM card, PCM/I2S/SPI, I2C, GPIO, ADC, USB Interfaces:UART, SIM card, PCM/I2S/SPI, I2C, GPIO, ADC, USB

Module LTE Cat.4 optimisé spécialement pour les applications M2M et IoT Quectel EG95 est une série de modules LTE de catégorie 4 optimisés spécialement pour les applications M2M et IoT. Adoptant la technologie 3GPP Rel. 11 LTE, il offre des débits de liaison descendant de 150 Mbit/s et des débits de liaisons 50Mbit/s. EG95 est compatible avec les modules Quectel UMTS/HSPA+ UG95/UG96 et Cat M1/Cat NB1 BG96. Cela le rend rétrocompatible avec les réseaux EDGE et GSM/GPRS existants, ce qui lui permet de migrer facilement des réseaux 2G/3G vers les réseaux 4G. Un riche ensemble de protocoles Internet, d’interfaces standard de l’industrie et de fonctionnalités abondantes étendent l’applicabilité du module à un large éventail d’applications M2M et IoT telles que routeur industriel, PDA industriel, pc tablette robuste, vidéosurveillance, signalisation numérique, et ainsi de suite. Principaux avantages ● Module LTE catégorie 4 optimisé pour les applications M2M et IoT

Facteur de forme du module M.2 (NGFF) de catégorie LTE Quectel EM05 is an LTE category 4 module adopting standard M.2 (NGFF) form factor. The space-saving M.2 form factor allows EM05 to be easily integrated into smaller and thinner devices. With a maximum data rate of 150Mbps downlink and 50Mbps uplink, it is optimized specially for M2M and IoT applications. EM05 contains three variants: EM05-CE, EM05-CML and EM05-E*, which can provide data connectivity on LTE-FDD, LTE-TDD, DC-HSDPA, HSPA+, HSDPA, HSUPA, WCDMA and CDMA networks. A rich set of Internet protocols, industry-standard interfaces and abundant functionalities (USB drivers for Windows XP, Windows Vista, Windows 7, Windows 8/8.1, Windows 10, Linux, Android/eCall*) extend the applicability of the module to a wide range of M2M applications such as industrial router, industrial PDA, rugged tablet PC, video surveillance and digital signage. Feature refinements:supports DFOTA, eCall* and DTMF

Nouvelle génération de modules Smart LTE Cat.4 multi-mode avec système d’exploitation Android intégré. Il prend également en charge la communication sans fil à courte portée via IEEE 802.11 b/g/n et BT4.1 LE. SC20 series is Quectel’s new generation of multi-mode Smart LTE Cat.4 modules with built-in Android OS. It contains five variants: SC20-CE, SC20-E, SC20-A, SC20-AU and SC20-J. SC20 series delivers speeds of 150Mbit/s downlink and 50Mbit/s uplink data rates. It is ideal for both industrial and consumer applications requiring the highest data-rate and high-speed internet access. SC20 series is backward-compatible with existing EDGE and GSM/GPRS networks, ensuring that it can be connected even in remote areas devoid of 3G or LTE coverage. It also supports short-range wireless communication via IEEE 802.11 b/g/n (SC20-E/-A/-AU/-J support IEEE 802.11 a/b/g/n) and BT4.1 LE.

LTE CATM1/NB-UIoT/GNSS Couverture mondiale 3GPP rel 14 Taille compact15x17 mmPower Save Mode(PSM) and Extended Discontinuous Reception(eDRX), SIM7070G can extend battery life to 10 years. • CAT-M, NB-IoT double mode • Support Bands: B1/B2/B3/B4/B5/B8/B12/B13/B14/B17/B18/B19/B20/B2 5/B26/B27/B28/B39/B66/B85 • Package 17.6x15.7mm / compatible with SIM868 • Interfaces: UART, SIM card, PCM/I2S/SPI, I2C, GPIO, ADC, USB • Cat-M: Uplink: 1119Kbps Downlink: 589Kbps • NB-IoT: Uplink: 150Kbps Downlink: 136Kbps Interfaces:UART, SIM card, PCM/I2S/SPI, I2C, GPIO, ADC, USB Cat-M: Uplink:1119Kbps Downlink:589Kbps NB-IoT: Uplink:150Kbps Downlink:136Kbps

Microcontrôleur à puce unique avec TCP/IP et 802.11 WLAN MAC/Baseband (32GPIOs, LQFP128) AX22001, Single Chip Microcontroller with TCP/IP and 802.11 WLAN MAC/Baseband, is a SystemonChip (SoC) solution which offers high performance dualCPU architecture with onchip 1MB shared Flash as Program Memory, onchip 64KB Data Memory for Main CPU (MCPU), onchip 32KB Data Memory for WiFi CPU (WCPU), TCP/IP accelerator, 802.11a/b/g compatible WLAN MAC/Baseband, Fast Ethernet MAC, and rich communication peripherals for wide varieties of application which need access to the wired/wireless LAN or Internet. The dualCPU architecture of AX22001 utilizes the MCPU for applications and TCP/IP processing, and the WCPU for WLAN protocol processing and Ethernet to WLAN packet format translation.

BC95-G est un module nb-ioT haute performance avec une consommation d’énergie extrêmement faible BC95-G est un module nb-ioT haute performance qui prend en charge plusieurs bandes de fréquences B1/B3/B8/B5/B20/B28* avec une consommation d’énergie extrêmement faible. Le profil ultra-compact de 23,6 mm × 19,9 mm × 2,2 mm en fait un choix parfait pour les applications sensibles à la taille. Conçu pour être compatible avec le module Quectel GSM/GPRS M95 dans le facteur de forme compact et unifié, il offre une plate-forme flexible et évolutive pour la migration des réseaux GSM/GPRS vers les réseaux NB-IoT. BC95-G adopte la technologie montée en surface, ce qui en fait une solution idéale pour des conceptions durables et robustes. Le profil bas et la petite taille du package LCC permettent à BC95-G d’être facilement intégré dans les applications limitées dans l’espace et de fournir une connectivité fiable avec les applications. Temps de mise sur le marché rapide:Conceptions de référence, outils d’évaluation et support technique en temps opportun minimisent

LTE Cat.1 Quectel EC21 est une série de modules LTE de catégorie 1 optimisés spécialement pour les applications M2M et IoT. Il dispose d’une connectivité LTE rentable et à faible puissance et offre des vitesses optimisées en M2M de 10 Mbit/s downlink et 5Mbit/s uplink. Celles-ci font d’EC21 une solution idéale pour de nombreuses applications IoT qui ne dépendent pas de la connectivité haute vitesse mais qui nécessitent toujours la longévité et la fiabilité des réseaux LTE. EC21 est compatible avec le module Quectel UMTS/HSPA+ UC20 et le module multi-mode LTE EC20/EC25 dans le facteur de forme compact et unifié. Il contient 9 variantes. Cela le rend rétrocompatible avec les réseaux EDGE et GSM/GPRS existants, ce qui lui permet de migrer facilement de LTE vers les réseaux 2G ou 3G. EC21 prend en charge la technologie de localisation Gen8C Lite de Qualcomm™® IZat (GPS, GLONASS, BeiDou, Galileo et QZSS). Améliorations des fonctionnalités:prend en charge DFOTA*, eCall*, QuecLocator et DTMF

The AX88180 is a highperformance and costeffective nonPCI Gigabit Ethernet controller for various embedded systems including consumer electronics and home network markets that require a higher bandwidth of network connectivity. The AX88180 supports 16/32bit SRAMlike interface and Gigabit Ethernet MAC, which is IEEE802.3 10BaseT, IEEE802.3u 100BaseT and IEEE802.3ab 1000BaseT compatible. The AX88180 supports fullduplex or halfduplex operation at 10/100/1000Mbps speed with autonegotiation or manual setting. The AX88180 integrates embedded SRAM for packet buffering to accommodate high bandwidth applications and supports IP/TCP/UDP checksum in hardware to offload processing loading from microprocessor/microcontroller in an embedded system. Highperformance nonPCI local bus Supports 16/32bit SRAMlike interface (US Patent Approval)

5G module

Clé USB 2.0 Capacity: 64 Go / USB : 2.0 Maximum write speed: 8 Mo/s Max read speed : 15 Mo/s Packaging: blister, 20 pc/carton Large choice of other equipments. Get in touch for prices and delivery!

Contrôleur Ethernet Gigabit USB3.0 à 10/100M AX88179 is the world's first USB 3.0 to Gigabit Ethernet controller which integrates USB 3.0 PHY and 10/100/1000Mbps Gigabit Ethernet MAC/PHY in a single chip. The AX88179 is the latest addition to ASIX's USBtoLAN product portfolio, providing a small form factor solution and plugandplay usability, enabling embedded system designers to deliver Gigabit Ethernet connectivity while leveraging the growth and speed of USB 3.0 SuperSpeed technology. AX88179 can be used in any embedded system with a USB host microcontroller requiring a twisted pair physical network connection. Featuring a USB interface (compliant with USB specification V3.0, V2.0 and V1.1) to communicate with a USB Host Controller, the AX88179 also integrates onchip

This document provides guidance on how to use the RDKGS12070 Reference Design board. It is recommended that the GS12070 Data Sheet (PDS061012) is read prior to reading this document in order to get familiarized with the features of the GS12070. The RDKGS12070 can be poweredup and evaluated outofthebox as a standalone kit without GUI control. Connecting to a PC (using the supplied USB cable) enables evaluation of the advanced features which are only accessible through the host interface. However, the following features are among those which are available outofthebox without any programming required MUX Mode with multiple conversion mode options DEMUX Mode with multiple conversion mode options Fourlane Bypass Mode for all supported rates including SD 75% colour bars pattern generator for all supported rates